Studio Journal
A Dental Office Floor Plan Checklist: 9 Things To Check Before You Sign A Lease
Before you sign a lease, draw the practice inside the space and check nine things: the operatory count, operatory width, access to every room, the restroom, working space around equipment, the sterilization room, the mechanical room, utilities, and room for growth. Each one is cheap to fix on a plan and expensive to fix after a build-out.
Why check a plan before the lease?
Because the lease fixes the walls you cannot move: the outline of the suite, the entrance, and often where water and drains can reach. A concept plan drawn first tells you whether your practice fits inside them. DDS.STUDIO runs most of the checks below automatically as you draw.
These are planning values, not building code or manufacturer specifications. A plan made in DDS.STUDIO is a concept plan, not construction documents. Confirm every dimension with your architect, your equipment supplier and your local code official before you build.
The checklist
1. Does your operatory count actually fit?
Enter the suite's square footage and the number of operatories you want on opening day. If the layouts only fit by shrinking every other room, the space is too small for that count.
2. Is every operatory at least 9 ft wide?
A chair with working space on both sides takes 6 ft 6 in before any cabinet. Below 9 ft there is no room for a side cabinet and a comfortable working position. See how big a dental operatory should be.
3. Can every room be reached from the entrance?
Every room needs a door, and there must be a walkable route from the front door to each one. Rooms that can only be reached through another room are worth a second look, especially sterilization and the lab.
4. Is the restroom large enough to be accessible?
DDS.STUDIO flags a restroom smaller than about 7 ft 6 in by 8 ft and a restroom door narrower than 3 ft. The reasons are two figures from the 2010 ADA Standards for Accessible Design: a circular turning space is 60 inches (5 ft) in diameter (section 304.3.1), and a door needs a clear opening of at least 32 inches (section 404.2.3), which a 3 ft door provides. Your architect will confirm the full requirements for your building.
5. Does the equipment have room to be used?
A piece of equipment needs more floor than its footprint. An autoclave is 2 ft square and needs 2 ft clear in front to load it. A panoramic X-ray unit is about 4 ft by 5 ft and needs a foot on each side and 1 ft 6 in in front. Check that this working space does not run into a wall or into the next item.
6. Does sterilization have a one-way flow?
Instruments should move in one direction, from dirty to clean, without crossing back. Put the room where every operatory can reach it without passing through the waiting area. See how to lay out a dental sterilization room.
7. Is there a mechanical room, and is it big enough?
A dental office needs a place for the air compressor and the vacuum pump, each about 2 ft 6 in by 2 ft with 1 ft 6 in of service space in front, plus an amalgam separator and water treatment. DDS.STUDIO plans a mechanical room at about 7 ft wide and never under 5 ft. Decide early where it goes, because it sets where the supply lines start.
8. Can the utilities reach?
Each item needs some mix of vacuum, air, water, drain, power and data. A patient chair needs the first five. Rooms that need a drain, such as operatories, sterilization and restrooms, are the hardest to place, so ask the landlord where the existing plumbing runs before you fix the layout.
9. Where does the next operatory go?
If you plan to add chairs later, draw those rooms now. DDS.STUDIO asks how many operatories you open with and how many you want ready to add, and lays out both, so the future rooms already have a place and a door.
What should I also watch for?
- Rooms that overlap or run outside the suite outline. Both are easy to draw by accident.
- The total area. Keep an eye on the square footage you have used against what the lease gives you.
Quick answers
What should I check in a dental office floor plan before signing a lease?
Check that your operatory count fits, every operatory is at least 9 ft wide, every room can be reached from the entrance, the restroom can hold a 5 ft turning circle, equipment has working space, sterilization flows one way, there is a mechanical room, utilities can reach, and there is room to add operatories later.
How big does an accessible restroom need to be in a dental office?
DDS.STUDIO plans for about 7 ft 6 in by 8 ft with a 3 ft door. That allows the 60 inch turning circle and the 32 inch clear door opening in the 2010 ADA Standards for Accessible Design. Confirm the full requirements with your architect.
Does a dental office need a mechanical room?
Yes. The air compressor, vacuum pump, amalgam separator and water treatment need a room of their own. DDS.STUDIO plans it at about 7 ft wide.